[GiDlist] Issues with Preprocess and Postprocess

Moderator: GiD Team

Maalik, Abdul

[GiDlist] Issues with Preprocess and Postprocess

Postby Maalik, Abdul » Fri Aug 01, 2014 9:49 pm

Thanks Enrique!

Now I have got another issue. Till yesterday, my GiD software was working perfectly but now it is giving me problem both in preprocess and postprocess. I have attached the screenshots of my preprocess window and the postprocess window. Moreover, I have also attached my project folder as well. The preprocess is not showing the geometry as it was showing before and postprocess is not showing any result. Can we see what is the problem? Is the problem with project folder or with the software itself?


Best Regards,
Abdul Maalik
PhD Student
ElectroScience Laboratory
Department of Electrial and Computer Engineering
Ohio State University
Columbus, OH 43212
USA

From: gidlist-bounces at listas.cimne.upc.edu [mailto:gidlist-bounces at listas.cimne.upc.edu] On Behalf Of Enrique Escolano
Sent: Friday, August 01, 2014 9:32 AM
To: gidlist at listas.cimne.upc.edu
Subject: Re: [GiDlist] Viewing results in GiD Postprocess

Instead of create graphs from menus, it is more comfortable to create them from the Graphs window (Window-View graphs...)
[cid:image001.jpg at 01CFADA8.63DD9250]
And to select the start and end points, if the center is an existing node, then you can simply pick it (or enter its id number).
If the mouse cursor is a "+" then GiD is expecting a new coordinate x,y,z but you can swap to pick an existing point with Ctrl-a (or click the contextual menu and select "Join")

If the center is not a node you must calculate its coordinates and enter the x,y,z
And for the end point you can calculate also its x,y,z or you can enter the coordinates relative to the previous point (the center) with this syntax starting by @

@x,y

Or with polar coordinates:

@radius,angle

I think that the polar option is what you want. Angle is in degrees, starting from x axe counter-clockwise
e.g. to go 0.2 units in a direction of 45 degrees enter

@0.2,45

Enrique Escolano


De: gidlist-bounces at listas.cimne.upc.edumailto:gidlist-bounces at listas.cimne.upc.edu [mailto:gidlist-bounces at listas.cimne.upc.edu] En nombre de Maalik, Abdul
Enviado el: viernes, 1 de agosto de 2014 2:03
Para: gidlist at listas.cimne.upc.edumailto:gidlist at listas.cimne.upc.edu
Asunto: [GiDlist] Viewing results in GiD Postprocess

Hi,

I have a 2D plot of current density of a circular plate. Now I want to plot the variation of current along a radial line (rho) at some given angle (phi).I know that I can go to

View results/Graphs/Line graph. Now I have two questions regarding this.


i) How can I specify the start and end point of the radial line ? (starting point should be center of circular plate and end point should be on the circumference of the plate)

ii) How can I specify the angle (with respect to horizontal axis) at which the radial line is to be drawn?


Best Regards,
Abdul Maalik
PhD Student
ElectroScience Laboratory
Department of Electrial and Computer Engineering
Ohio State University
Columbus, OH 43212
USA

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140801/6fb7e70b/attachment-0001.htm
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.jpg
Type: image/jpeg
Size: 14033 bytes
Desc: image001.jpg
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140801/6fb7e70b/attachment-0001.jpg
-------------- next part --------------
A non-text attachment was scrubbed...
Name: CenterFedRef10G.gid.rar
Type: application/octet-stream
Size: 412317 bytes
Desc: CenterFedRef10G.gid.rar
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140801/6fb7e70b/attachment-0001.obj
-------------- next part --------------
A non-text attachment was scrubbed...
Name: preprocess problem.png
Type: image/png
Size: 28619 bytes
Desc: preprocess problem.png
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140801/6fb7e70b/attachment-0002.png
-------------- next part --------------
A non-text attachment was scrubbed...
Name: postprocess problem.png
Type: image/png
Size: 62022 bytes
Desc: postprocess problem.png
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140801/6fb7e70b/attachment-0003.png
HEMMI, Shigeru

[GiDlist] Import->Insert GiD Geometry crashes on Windows 64b

Postby HEMMI, Shigeru » Mon Aug 04, 2014 1:21 pm

Dear Enrique Escolano,

1. As you wrote, GiD 11.1.9d does not crash after mesh generated for
both models and I apply "Insert GiD model"; thanks for the support.
2. I do not have money to purchase GiD 12; I have to go with GiD 11 for a while.
3. The last official version 11.0.8 still has another crash problem, e.g.,
http://www.gidhome.com/component/manual/gidlist2014/panhteonigs_causes_a_crash_of_gid_11_64bit_whengenerating_mesh
, which is not replyed yet. In my experiences the official version
11.0.8 crashes very often in many situations.

Best regards,

HEMMI, Shigeru



2014-08-04 19:46 GMT+09:00 Enrique Escolano escolano at cimne.upc.edu:
If fact the problem happen because in latest GiD developer versions "Insert GiD geometry" has changed to "Insert GiD model" and now the mesh is also inserted.

The crash happen if the model to insert or the current model doesn't has any mesh. You can avoid the crash in GiD 11.1.9d with some trick, like generate a mesh in both models before the insertion.

The problem is that we are not compiling any 11.x version more, because this version has become the 12 version. The bug has been fixed in version 12.0.1 available for download now.

You can also use the last 11.0.8 official version.

Enrique Escolano

-----Mensaje original-----
De: HEMMI, Shigeru [mailto:textdirected at gmail.com]
Enviado el: domingo, 3 de agosto de 2014 14:52
Para: Enrique Escolano
Asunto: Re: [GiDlist] Import-Insert GiD Geometry crashes on Windows 64bit

Dear Enrique,

Thanks for the answer but the problem NOT solved.

I saved two models, for example, one is a sphere of radius 1.0 and the center placed at the origin, and the second model of another sphere of radius 1.0 at the center (2.0,0,0). When I open the first model and go to "import--insert GiD Geometry" choosing the second model, GiD crashes on my Windows PC.

Since the "import--insert GiD Geomtry" feature is significant for my work, please fix it and provide fixed GiD 11 module.

Best regards,

HEMMI, Shigeru

2014-07-30 18:14 GMT+09:00 Enrique Escolano escolano at cimne.upc.edu:
It seems that it crash only when inserting a model in an empty model.
For this case doesn't has sense to use insert, use the normal open.
Insert model is just interesting to add a model to an existing model.

We will fix it for next GiD 12.0.1 version

Thanks for your information

Enrique

-----Mensaje original-----
De: gidlist-bounces at listas.cimne.upc.edu
[mailto:gidlist-bounces at listas.cimne.upc.edu] En nombre de HEMMI,
Shigeru Enviado el: martes, 29 de julio de 2014 23:41
Para: gidlist at listas.cimne.upc.edu
Asunto: [GiDlist] Import-Insert GiD Geometry crashes on Windows 64bit

Dear GiD team,

I have a problem of GiD crash.

When I try
Files--Import--Insert GiD model
and choose some model then crash.

I am using GiD 11.1.9d 64bit on Windows 8.1 pro 64bit.

Thanks in advance,

HEMMI, Shigeru
_______________________________________________
GiDlist mailing list
GiDlist at listas.cimne.upc.edu
http://listas.cimne.upc.edu/cgi-bin/mailman/listinfo/gidlist


User avatar
escolano
Posts: 1568
Joined: Thu Sep 18, 2014 3:31 pm

[GiDlist] Issues with Preprocess and Postprocess

Postby escolano » Mon Aug 04, 2014 2:29 pm

Your file CenterFedRef10G.post.msh really does not contain a GiD
postprocess mesh, it contain a NASTRAN mesh !!

And your preprocess model is empty (there are not geometric or mesh
entities)



You can rename CenterFedRef10G.post.msh to CenterFedRef10G.nas, then open
the GiD project CenterFedRef10G and import it with Files-Import-NASTRAN
mesh.

And then you change to postprocess the results file is read and you can see
it.



After import the Nastran file you can save the model, and then the
preprocess mesh is saved as CenterFedRef10G.msh with the GiD preprocess
binary format, and then you can load again the model without require
importing the Nastran file (in fact you can delete it after the import)



Regards



Enrique Escolano



De: gidlist-bounces at listas.cimne.upc.edu
[mailto:gidlist-bounces at listas.cimne.upc.edu] En nombre de Maalik, Abdul
Enviado el: viernes, 1 de agosto de 2014 22:50
Para: gidlist at listas.cimne.upc.edu
Asunto: [GiDlist] Issues with Preprocess and Postprocess



Thanks Enrique!



Now I have got another issue. Till yesterday, my GiD software was working
perfectly but now it is giving me problem both in preprocess and
postprocess. I have attached the screenshots of my preprocess window and the
postprocess window. Moreover, I have also attached my project folder as
well. The preprocess is not showing the geometry as it was showing before
and postprocess is not showing any result. Can we see what is the problem?
Is the problem with project folder or with the software itself?





Best Regards,

Abdul Maalik

PhD Student

ElectroScience Laboratory

Department of Electrial and Computer Engineering

Ohio State University

Columbus, OH 43212

USA



From: gidlist-bounces at listas.cimne.upc.edu
[mailto:gidlist-bounces at listas.cimne.upc.edu] On Behalf Of Enrique Escolano
Sent: Friday, August 01, 2014 9:32 AM
To: gidlist at listas.cimne.upc.edu
Subject: Re: [GiDlist] Viewing results in GiD Postprocess



Instead of create graphs from menus, it is more comfortable to create them
from the Graphs window (Window-View graphs.)



And to select the start and end points, if the center is an existing node,
then you can simply pick it (or enter its id number).

If the mouse cursor is a "+" then GiD is expecting a new coordinate x,y,z
but you can swap to pick an existing point with Ctrl-a (or click the
contextual menu and select "Join")



If the center is not a node you must calculate its coordinates and enter the
x,y,z

And for the end point you can calculate also its x,y,z or you can enter the
coordinates relative to the previous point (the center) with this syntax
starting by @



@x,y



Or with polar coordinates:



@radius,angle



I think that the polar option is what you want. Angle is in degrees,
starting from x axe counter-clockwise

e.g. to go 0.2 units in a direction of 45 degrees enter



@0.2,45



Enrique Escolano





De: gidlist-bounces at listas.cimne.upc.edu
[mailto:gidlist-bounces at listas.cimne.upc.edu] En nombre de Maalik, Abdul
Enviado el: viernes, 1 de agosto de 2014 2:03
Para: gidlist at listas.cimne.upc.edu
Asunto: [GiDlist] Viewing results in GiD Postprocess



Hi,



I have a 2D plot of current density of a circular plate. Now I want to plot
the variation of current along a radial line (rho) at some given angle
(phi).I know that I can go to



View results/Graphs/Line graph. Now I have two questions regarding this.



i) How can I specify the start and end point of the
radial line ? (starting point should be center of circular plate and end
point should be on the circumference of the plate)

ii) How can I specify the angle (with respect to
horizontal axis) at which the radial line is to be drawn?





Best Regards,

Abdul Maalik

PhD Student

ElectroScience Laboratory

Department of Electrial and Computer Engineering

Ohio State University

Columbus, OH 43212

USA



-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140804/3c8c2fae/attachment-0001.htm
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: image/jpeg
Size: 14033 bytes
Desc: not available
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140804/3c8c2fae/attachment-0001.jpeg
User avatar
escolano
Posts: 1568
Joined: Thu Sep 18, 2014 3:31 pm

[GiDlist] Import->Insert GiD Geometry crashes on Windows 64b

Postby escolano » Mon Aug 04, 2014 3:14 pm

In my experience GiD 11.0.8 is not so unstable as do you think.
Maybe do you have some settings of a kind of models that are specially
problematic.
I recommend you to reset all your settings (start once with "GiD safe mode"
and set the 'Reset preferences' checkbox)

For example I am able to import the file pantheon.igs with GiD 11.0.8
(Windows x32) , with automatic collapse with default tolerance with
importing,
And then to generate the mesh with size=100 I have some problem: GiD can't
mesh, but it doesn't crashed.
Then I've deleted the volume and created it again (maybe some surface is
bad oriented for the volume) and then I am able to mesh it with this size.
I attach my GiD model including the coarse volume mesh.

Enrique

-----Mensaje original-----
De: gidlist-bounces at listas.cimne.upc.edu
[mailto:gidlist-bounces at listas.cimne.upc.edu] En nombre de HEMMI, Shigeru
Enviado el: lunes, 4 de agosto de 2014 14:21
Para: Enrique Escolano; gidlist at listas.cimne.upc.edu
Asunto: Re: [GiDlist] Import-Insert GiD Geometry crashes on Windows 64bit

Dear Enrique Escolano,

1. As you wrote, GiD 11.1.9d does not crash after mesh generated for both
models and I apply "Insert GiD model"; thanks for the support.
2. I do not have money to purchase GiD 12; I have to go with GiD 11 for a
while.
3. The last official version 11.0.8 still has another crash problem, e.g.,

http://www.gidhome.com/component/manual/gidlist2014/panhteonigs_causes_a_cra
sh_of_gid_11_64bit_whengenerating_mesh
, which is not replyed yet. In my experiences the official version
11.0.8 crashes very often in many situations.

Best regards,

HEMMI, Shigeru



2014-08-04 19:46 GMT+09:00 Enrique Escolano escolano at cimne.upc.edu:
If fact the problem happen because in latest GiD developer versions
"Insert GiD geometry" has changed to "Insert GiD model" and now the mesh is
also inserted.

The crash happen if the model to insert or the current model doesn't has
any mesh. You can avoid the crash in GiD 11.1.9d with some trick, like
generate a mesh in both models before the insertion.

The problem is that we are not compiling any 11.x version more, because
this version has become the 12 version. The bug has been fixed in version
12.0.1 available for download now.

You can also use the last 11.0.8 official version.

Enrique Escolano

-----Mensaje original-----
De: HEMMI, Shigeru [mailto:textdirected at gmail.com] Enviado el:
domingo, 3 de agosto de 2014 14:52
Para: Enrique Escolano
Asunto: Re: [GiDlist] Import-Insert GiD Geometry crashes on Windows
64bit

Dear Enrique,

Thanks for the answer but the problem NOT solved.

I saved two models, for example, one is a sphere of radius 1.0 and the
center placed at the origin, and the second model of another sphere of
radius 1.0 at the center (2.0,0,0). When I open the first model and go to
"import--insert GiD Geometry" choosing the second model, GiD crashes on my
Windows PC.

Since the "import--insert GiD Geomtry" feature is significant for my
work, please fix it and provide fixed GiD 11 module.

Best regards,

HEMMI, Shigeru

2014-07-30 18:14 GMT+09:00 Enrique Escolano escolano at cimne.upc.edu:
It seems that it crash only when inserting a model in an empty model.
For this case doesn't has sense to use insert, use the normal open.
Insert model is just interesting to add a model to an existing model.

We will fix it for next GiD 12.0.1 version

Thanks for your information

Enrique

-----Mensaje original-----
De: gidlist-bounces at listas.cimne.upc.edu
[mailto:gidlist-bounces at listas.cimne.upc.edu] En nombre de HEMMI,
Shigeru Enviado el: martes, 29 de julio de 2014 23:41
Para: gidlist at listas.cimne.upc.edu
Asunto: [GiDlist] Import-Insert GiD Geometry crashes on Windows
64bit

Dear GiD team,

I have a problem of GiD crash.

When I try
Files--Import--Insert GiD model
and choose some model then crash.

I am using GiD 11.1.9d 64bit on Windows 8.1 pro 64bit.

Thanks in advance,

HEMMI, Shigeru
_______________________________________________
GiDlist mailing list
GiDlist at listas.cimne.upc.edu
http://listas.cimne.upc.edu/cgi-bin/mailman/listinfo/gidlist


_______________________________________________
GiDlist mailing list
GiDlist at listas.cimne.upc.edu
http://listas.cimne.upc.edu/cgi-bin/mailman/listinfo/gidlist
-------------- next part --------------
A non-text attachment was scrubbed...
Name: pantheon.zip
Type: application/octet-stream
Size: 6594626 bytes
Desc: not available
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140804/0766ce1b/attachment-0001.obj
Maalik, Abdul

[GiDlist] Issues with Preprocess and Postprocess

Postby Maalik, Abdul » Wed Aug 06, 2014 4:01 am

Thanks a lot, Enrique.

One more thing regarding postprocess! In my post process, I am getting following warning message.

"Sorry, but to get shinny textured contour fill OpenGL v. 1.2 or the GL_EXT_separate_specular_color extension is needed."

How can I get rid of this warning message? I have also attached the screenshot of my postprocess.


Regards,
Abdul Maalik
PhD Student
ElectroScience Laboratory
Department of Electrial and Computer Engineering
Ohio State University
Columbus, OH 43212
USA

From: gidlist-bounces at listas.cimne.upc.edu [mailto:gidlist-bounces at listas.cimne.upc.edu] On Behalf Of Enrique Escolano
Sent: Monday, August 04, 2014 9:29 AM
To: gidlist at listas.cimne.upc.edu
Subject: Re: [GiDlist] Issues with Preprocess and Postprocess

Your file CenterFedRef10G.post.msh really does not contain a GiD postprocess mesh, it contain a NASTRAN mesh !!
And your preprocess model is empty (there are not geometric or mesh entities)

You can rename CenterFedRef10G.post.msh to CenterFedRef10G.nas, then open the GiD project CenterFedRef10G and import it with Files-Import-NASTRAN mesh...
And then you change to postprocess the results file is read and you can see it.

After import the Nastran file you can save the model, and then the preprocess mesh is saved as CenterFedRef10G.msh with the GiD preprocess binary format, and then you can load again the model without require importing the Nastran file (in fact you can delete it after the import)

Regards

Enrique Escolano

De: gidlist-bounces at listas.cimne.upc.edumailto:gidlist-bounces at listas.cimne.upc.edu [mailto:gidlist-bounces at listas.cimne.upc.edu] En nombre de Maalik, Abdul
Enviado el: viernes, 1 de agosto de 2014 22:50
Para: gidlist at listas.cimne.upc.edumailto:gidlist at listas.cimne.upc.edu
Asunto: [GiDlist] Issues with Preprocess and Postprocess

Thanks Enrique!

Now I have got another issue. Till yesterday, my GiD software was working perfectly but now it is giving me problem both in preprocess and postprocess. I have attached the screenshots of my preprocess window and the postprocess window. Moreover, I have also attached my project folder as well. The preprocess is not showing the geometry as it was showing before and postprocess is not showing any result. Can we see what is the problem? Is the problem with project folder or with the software itself?


Best Regards,
Abdul Maalik
PhD Student
ElectroScience Laboratory
Department of Electrial and Computer Engineering
Ohio State University
Columbus, OH 43212
USA

From: gidlist-bounces at listas.cimne.upc.edumailto:gidlist-bounces at listas.cimne.upc.edu [mailto:gidlist-bounces at listas.cimne.upc.edu] On Behalf Of Enrique Escolano
Sent: Friday, August 01, 2014 9:32 AM
To: gidlist at listas.cimne.upc.edumailto:gidlist at listas.cimne.upc.edu
Subject: Re: [GiDlist] Viewing results in GiD Postprocess

Instead of create graphs from menus, it is more comfortable to create them from the Graphs window (Window-View graphs...)
[cid:image001.jpg at 01CFB101.2E2034E0]
And to select the start and end points, if the center is an existing node, then you can simply pick it (or enter its id number).
If the mouse cursor is a "+" then GiD is expecting a new coordinate x,y,z but you can swap to pick an existing point with Ctrl-a (or click the contextual menu and select "Join")

If the center is not a node you must calculate its coordinates and enter the x,y,z
And for the end point you can calculate also its x,y,z or you can enter the coordinates relative to the previous point (the center) with this syntax starting by @

@x,y

Or with polar coordinates:

@radius,angle

I think that the polar option is what you want. Angle is in degrees, starting from x axe counter-clockwise
e.g. to go 0.2 units in a direction of 45 degrees enter

@0.2,45

Enrique Escolano


De: gidlist-bounces at listas.cimne.upc.edumailto:gidlist-bounces at listas.cimne.upc.edu [mailto:gidlist-bounces at listas.cimne.upc.edu] En nombre de Maalik, Abdul
Enviado el: viernes, 1 de agosto de 2014 2:03
Para: gidlist at listas.cimne.upc.edumailto:gidlist at listas.cimne.upc.edu
Asunto: [GiDlist] Viewing results in GiD Postprocess

Hi,

I have a 2D plot of current density of a circular plate. Now I want to plot the variation of current along a radial line (rho) at some given angle (phi).I know that I can go to

View results/Graphs/Line graph. Now I have two questions regarding this.


i) How can I specify the start and end point of the radial line ? (starting point should be center of circular plate and end point should be on the circumference of the plate)

ii) How can I specify the angle (with respect to horizontal axis) at which the radial line is to be drawn?


Best Regards,
Abdul Maalik
PhD Student
ElectroScience Laboratory
Department of Electrial and Computer Engineering
Ohio State University
Columbus, OH 43212
USA

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140806/11ff179f/attachment-0001.htm
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.jpg
Type: image/jpeg
Size: 14033 bytes
Desc: image001.jpg
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140806/11ff179f/attachment-0001.jpg
-------------- next part --------------
A non-text attachment was scrubbed...
Name: postprocess.png
Type: image/png
Size: 210106 bytes
Desc: postprocess.png
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140806/11ff179f/attachment-0001.png
User avatar
miguel
Posts: 344
Joined: Thu Sep 25, 2014 9:04 am

[GiDlist] Issues with Preprocess and Postprocess

Postby miguel » Wed Aug 06, 2014 12:30 pm

Hi,

from the message i guess that you're using GiD in Safe visualization mode,
i.e. using software (cpu) graphics.

To disable the message, in post-process, select the option Options --
Contour -- Bright color -- No from the top menu bar.

Without this option, contour fill colours will be drawn without shininess,
kind of metal reflection.



If you want to use this option, i'll recomend you to change to Fast
visualization mode ( Preferences window -- Graphics -- system), which will
use your graphics card to render the models.

Have you tried already this mode? did you find any problems? If so, can you
explain them to us and send the contents of Help -- About -- More?



thanks, and best regards,



Miguel Pasenau



De: gidlist-bounces at listas.cimne.upc.edu
[mailto:gidlist-bounces at listas.cimne.upc.edu] En nombre de Maalik, Abdul
Enviado el: miércoles, 06 de agosto de 2014 5:01
Para: gidlist at listas.cimne.upc.edu
Asunto: Re: [GiDlist] Issues with Preprocess and Postprocess



Thanks a lot, Enrique.



One more thing regarding postprocess! In my post process, I am getting
following warning message.



“Sorry, but to get shinny textured contour fill OpenGL v. 1.2 or the
GL_EXT_separate_specular_color extension is needed.”



How can I get rid of this warning message? I have also attached the
screenshot of my postprocess.





Regards,

Abdul Maalik

PhD Student

ElectroScience Laboratory

Department of Electrial and Computer Engineering

Ohio State University

Columbus, OH 43212

USA



From: gidlist-bounces at listas.cimne.upc.edu
[mailto:gidlist-bounces at listas.cimne.upc.edu] On Behalf Of Enrique Escolano
Sent: Monday, August 04, 2014 9:29 AM
To: gidlist at listas.cimne.upc.edu
Subject: Re: [GiDlist] Issues with Preprocess and Postprocess



Your file CenterFedRef10G.post.msh really does not contain a GiD
postprocess mesh, it contain a NASTRAN mesh !!

And your preprocess model is empty (there are not geometric or mesh
entities)



You can rename CenterFedRef10G.post.msh to CenterFedRef10G.nas, then open
the GiD project CenterFedRef10G and import it with Files-Import-NASTRAN
mesh


And then you change to postprocess the results file is read and you can see
it.



After import the Nastran file you can save the model, and then the
preprocess mesh is saved as CenterFedRef10G.msh with the GiD preprocess
binary format, and then you can load again the model without require
importing the Nastran file (in fact you can delete it after the import)



Regards



Enrique Escolano



De: gidlist-bounces at listas.cimne.upc.edu
[mailto:gidlist-bounces at listas.cimne.upc.edu] En nombre de Maalik, Abdul
Enviado el: viernes, 1 de agosto de 2014 22:50
Para: gidlist at listas.cimne.upc.edu
Asunto: [GiDlist] Issues with Preprocess and Postprocess



Thanks Enrique!



Now I have got another issue. Till yesterday, my GiD software was working
perfectly but now it is giving me problem both in preprocess and
postprocess. I have attached the screenshots of my preprocess window and the
postprocess window. Moreover, I have also attached my project folder as
well. The preprocess is not showing the geometry as it was showing before
and postprocess is not showing any result. Can we see what is the problem?
Is the problem with project folder or with the software itself?





Best Regards,

Abdul Maalik

PhD Student

ElectroScience Laboratory

Department of Electrial and Computer Engineering

Ohio State University

Columbus, OH 43212

USA



From: gidlist-bounces at listas.cimne.upc.edu
[mailto:gidlist-bounces at listas.cimne.upc.edu] On Behalf Of Enrique Escolano
Sent: Friday, August 01, 2014 9:32 AM
To: gidlist at listas.cimne.upc.edu
Subject: Re: [GiDlist] Viewing results in GiD Postprocess



Instead of create graphs from menus, it is more comfortable to create them
from the Graphs window (Window-View graphs
)



And to select the start and end points, if the center is an existing node,
then you can simply pick it (or enter its id number).

If the mouse cursor is a “+” then GiD is expecting a new coordinate x,y,z
but you can swap to pick an existing point with Ctrl-a (or click the
contextual menu and select “Join”)



If the center is not a node you must calculate its coordinates and enter the
x,y,z

And for the end point you can calculate also its x,y,z or you can enter the
coordinates relative to the previous point (the center) with this syntax
starting by @



@x,y



Or with polar coordinates:



@radius,angle



I think that the polar option is what you want. Angle is in degrees,
starting from x axe counter-clockwise

e.g. to go 0.2 units in a direction of 45 degrees enter



@0.2,45



Enrique Escolano





De: gidlist-bounces at listas.cimne.upc.edu
[mailto:gidlist-bounces at listas.cimne.upc.edu] En nombre de Maalik, Abdul
Enviado el: viernes, 1 de agosto de 2014 2:03
Para: gidlist at listas.cimne.upc.edu
Asunto: [GiDlist] Viewing results in GiD Postprocess



Hi,



I have a 2D plot of current density of a circular plate. Now I want to plot
the variation of current along a radial line (rho) at some given angle
(phi).I know that I can go to



View results/Graphs/Line graph. Now I have two questions regarding this.



i) How can I specify the start and end point of the
radial line ? (starting point should be center of circular plate and end
point should be on the circumference of the plate)

ii) How can I specify the angle (with respect to
horizontal axis) at which the radial line is to be drawn?





Best Regards,

Abdul Maalik

PhD Student

ElectroScience Laboratory

Department of Electrial and Computer Engineering

Ohio State University

Columbus, OH 43212

USA





---
Este mensaje no contiene virus ni malware porque la protección de avast! Antivirus está activa.
http://www.avast.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140806/92ce686f/attachment-0001.htm
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: image/jpeg
Size: 14033 bytes
Desc: not available
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140806/92ce686f/attachment-0001.jpeg
HEMMI, Shigeru

[GiDlist] Import->Insert GiD Geometry crashes on Windows 64b

Postby HEMMI, Shigeru » Wed Aug 06, 2014 12:30 pm

Dear Enrique Escolano,

Thanks for the support but the problem not solved.

Uninstalled GiD11.1.9d-win-x64-Install and installed GiD11.0.8-win-x64,
set the 'Reset preferences' checkbox, and
open pantheon.gid which is the attachment in your reply mail.

And then I did Erase--Mesh and Generate--Mesh, GiD crashed again.
See the attachment 2 figures.

My PC is Windows 8.1 Pro, 32Gbytes memory equipped.

Best regards,

HEMMI, Shigeru

2014-08-04 23:14 GMT+09:00 Enrique Escolano escolano at cimne.upc.edu:
In my experience GiD 11.0.8 is not so unstable as do you think.
Maybe do you have some settings of a kind of models that are specially
problematic.
I recommend you to reset all your settings (start once with "GiD safe mode"
and set the 'Reset preferences' checkbox)

For example I am able to import the file pantheon.igs with GiD 11.0.8
(Windows x32) , with automatic collapse with default tolerance with
importing,
And then to generate the mesh with size=100 I have some problem: GiD can't
mesh, but it doesn't crashed.
Then I've deleted the volume and created it again (maybe some surface is
bad oriented for the volume) and then I am able to mesh it with this size.
I attach my GiD model including the coarse volume mesh.

Enrique

-----Mensaje original-----
De: gidlist-bounces at listas.cimne.upc.edu
[mailto:gidlist-bounces at listas.cimne.upc.edu] En nombre de HEMMI, Shigeru
Enviado el: lunes, 4 de agosto de 2014 14:21
Para: Enrique Escolano; gidlist at listas.cimne.upc.edu
Asunto: Re: [GiDlist] Import-Insert GiD Geometry crashes on Windows 64bit

Dear Enrique Escolano,

1. As you wrote, GiD 11.1.9d does not crash after mesh generated for both
models and I apply "Insert GiD model"; thanks for the support.
2. I do not have money to purchase GiD 12; I have to go with GiD 11 for a
while.
3. The last official version 11.0.8 still has another crash problem, e.g.,

http://www.gidhome.com/component/manual/gidlist2014/panhteonigs_causes_a_cra
sh_of_gid_11_64bit_whengenerating_mesh
, which is not replyed yet. In my experiences the official version
11.0.8 crashes very often in many situations.

Best regards,

HEMMI, Shigeru



2014-08-04 19:46 GMT+09:00 Enrique Escolano escolano at cimne.upc.edu:
If fact the problem happen because in latest GiD developer versions
"Insert GiD geometry" has changed to "Insert GiD model" and now the mesh is
also inserted.

The crash happen if the model to insert or the current model doesn't has
any mesh. You can avoid the crash in GiD 11.1.9d with some trick, like
generate a mesh in both models before the insertion.

The problem is that we are not compiling any 11.x version more, because
this version has become the 12 version. The bug has been fixed in version
12.0.1 available for download now.

You can also use the last 11.0.8 official version.

Enrique Escolano

-----Mensaje original-----
De: HEMMI, Shigeru [mailto:textdirected at gmail.com] Enviado el:
domingo, 3 de agosto de 2014 14:52
Para: Enrique Escolano
Asunto: Re: [GiDlist] Import-Insert GiD Geometry crashes on Windows
64bit

Dear Enrique,

Thanks for the answer but the problem NOT solved.

I saved two models, for example, one is a sphere of radius 1.0 and the
center placed at the origin, and the second model of another sphere of
radius 1.0 at the center (2.0,0,0). When I open the first model and go to
"import--insert GiD Geometry" choosing the second model, GiD crashes on my
Windows PC.

Since the "import--insert GiD Geomtry" feature is significant for my
work, please fix it and provide fixed GiD 11 module.

Best regards,

HEMMI, Shigeru

2014-07-30 18:14 GMT+09:00 Enrique Escolano escolano at cimne.upc.edu:
It seems that it crash only when inserting a model in an empty model.
For this case doesn't has sense to use insert, use the normal open.
Insert model is just interesting to add a model to an existing model.

We will fix it for next GiD 12.0.1 version

Thanks for your information

Enrique

-----Mensaje original-----
De: gidlist-bounces at listas.cimne.upc.edu
[mailto:gidlist-bounces at listas.cimne.upc.edu] En nombre de HEMMI,
Shigeru Enviado el: martes, 29 de julio de 2014 23:41
Para: gidlist at listas.cimne.upc.edu
Asunto: [GiDlist] Import-Insert GiD Geometry crashes on Windows
64bit

Dear GiD team,

I have a problem of GiD crash.

When I try
Files--Import--Insert GiD model
and choose some model then crash.

I am using GiD 11.1.9d 64bit on Windows 8.1 pro 64bit.

Thanks in advance,

HEMMI, Shigeru
_______________________________________________
GiDlist mailing list
GiDlist at listas.cimne.upc.edu
http://listas.cimne.upc.edu/cgi-bin/mailman/listinfo/gidlist


_______________________________________________
GiDlist mailing list
GiDlist at listas.cimne.upc.edu
http://listas.cimne.upc.edu/cgi-bin/mailman/listinfo/gidlist
-------------- next part --------------
A non-text attachment was scrubbed...
Name: GiDcrash_Fig1.png
Type: image/png
Size: 140942 bytes
Desc: not available
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140806/8a93c921/attachment-0002.png
-------------- next part --------------
A non-text attachment was scrubbed...
Name: GiDcrash_Fig2.png
Type: image/png
Size: 184512 bytes
Desc: not available
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140806/8a93c921/attachment-0003.png
User avatar
escolano
Posts: 1568
Joined: Thu Sep 18, 2014 3:31 pm

[GiDlist] Import->Insert GiD Geometry crashes on Windows 64b

Postby escolano » Wed Aug 06, 2014 2:07 pm

You can set exactly the same meshing preferences than I've used opening my GiD model and selecting the menu
Mesh-Mesh options from model

I've used GiD 11.0.8 Windows x32, maybe the crash only happen in the Windows x64 version (I don't have now any Winx64 machine available to test it)
You can also install and run a Windows x32 version of GiD on a Window x64 operating system.

Note: you can have several GiD versions installed simultaneously, it is not necessary to uninstall other versions, each one is stored in a different folder.

-----Mensaje original-----
De: HEMMI, Shigeru [mailto:textdirected at gmail.com]
Enviado el: miércoles, 6 de agosto de 2014 13:30
Para: Enrique Escolano; gidlist at listas.cimne.upc.edu
Asunto: Re: [GiDlist] Import-Insert GiD Geometry crashes on Windows 64bit

Dear Enrique Escolano,

Thanks for the support but the problem not solved.

Uninstalled GiD11.1.9d-win-x64-Install and installed GiD11.0.8-win-x64, set the 'Reset preferences' checkbox, and open pantheon.gid which is the attachment in your reply mail.

And then I did Erase--Mesh and Generate--Mesh, GiD crashed again.
See the attachment 2 figures.

My PC is Windows 8.1 Pro, 32Gbytes memory equipped.

Best regards,

HEMMI, Shigeru

2014-08-04 23:14 GMT+09:00 Enrique Escolano escolano at cimne.upc.edu:
In my experience GiD 11.0.8 is not so unstable as do you think.
Maybe do you have some settings of a kind of models that are specially
problematic.
I recommend you to reset all your settings (start once with "GiD safe mode"
and set the 'Reset preferences' checkbox)

For example I am able to import the file pantheon.igs with GiD 11.0.8
(Windows x32) , with automatic collapse with default tolerance with
importing, And then to generate the mesh with size=100 I have some
problem: GiD can't mesh, but it doesn't crashed.
Then I've deleted the volume and created it again (maybe some surface
is bad oriented for the volume) and then I am able to mesh it with this size.
I attach my GiD model including the coarse volume mesh.

Enrique

-----Mensaje original-----
De: gidlist-bounces at listas.cimne.upc.edu
[mailto:gidlist-bounces at listas.cimne.upc.edu] En nombre de HEMMI,
Shigeru Enviado el: lunes, 4 de agosto de 2014 14:21
Para: Enrique Escolano; gidlist at listas.cimne.upc.edu
Asunto: Re: [GiDlist] Import-Insert GiD Geometry crashes on Windows
64bit

Dear Enrique Escolano,

1. As you wrote, GiD 11.1.9d does not crash after mesh generated for
both models and I apply "Insert GiD model"; thanks for the support.
2. I do not have money to purchase GiD 12; I have to go with GiD 11
for a while.
3. The last official version 11.0.8 still has another crash problem,
e.g.,

http://www.gidhome.com/component/manual/gidlist2014/panhteonigs_causes
_a_cra sh_of_gid_11_64bit_whengenerating_mesh
, which is not replyed yet. In my experiences the official version
11.0.8 crashes very often in many situations.

Best regards,

HEMMI, Shigeru



2014-08-04 19:46 GMT+09:00 Enrique Escolano escolano at cimne.upc.edu:
If fact the problem happen because in latest GiD developer versions
"Insert GiD geometry" has changed to "Insert GiD model" and now the
mesh is also inserted.

The crash happen if the model to insert or the current model doesn't
has
any mesh. You can avoid the crash in GiD 11.1.9d with some trick, like
generate a mesh in both models before the insertion.

The problem is that we are not compiling any 11.x version more,
because
this version has become the 12 version. The bug has been fixed in
version
12.0.1 available for download now.

You can also use the last 11.0.8 official version.

Enrique Escolano

-----Mensaje original-----
De: HEMMI, Shigeru [mailto:textdirected at gmail.com] Enviado el:
domingo, 3 de agosto de 2014 14:52
Para: Enrique Escolano
Asunto: Re: [GiDlist] Import-Insert GiD Geometry crashes on Windows
64bit

Dear Enrique,

Thanks for the answer but the problem NOT solved.

I saved two models, for example, one is a sphere of radius 1.0 and
the
center placed at the origin, and the second model of another sphere
of radius 1.0 at the center (2.0,0,0). When I open the first model and
go to "import--insert GiD Geometry" choosing the second model, GiD
crashes on my Windows PC.

Since the "import--insert GiD Geomtry" feature is significant for my
work, please fix it and provide fixed GiD 11 module.

Best regards,

HEMMI, Shigeru

2014-07-30 18:14 GMT+09:00 Enrique Escolano escolano at cimne.upc.edu:
It seems that it crash only when inserting a model in an empty model.
For this case doesn't has sense to use insert, use the normal open.
Insert model is just interesting to add a model to an existing model.

We will fix it for next GiD 12.0.1 version

Thanks for your information

Enrique

-----Mensaje original-----
De: gidlist-bounces at listas.cimne.upc.edu
[mailto:gidlist-bounces at listas.cimne.upc.edu] En nombre de HEMMI,
Shigeru Enviado el: martes, 29 de julio de 2014 23:41
Para: gidlist at listas.cimne.upc.edu
Asunto: [GiDlist] Import-Insert GiD Geometry crashes on Windows
64bit

Dear GiD team,

I have a problem of GiD crash.

When I try
Files--Import--Insert GiD model
and choose some model then crash.

I am using GiD 11.1.9d 64bit on Windows 8.1 pro 64bit.

Thanks in advance,

HEMMI, Shigeru
_______________________________________________
GiDlist mailing list
GiDlist at listas.cimne.upc.edu
http://listas.cimne.upc.edu/cgi-bin/mailman/listinfo/gidlist


_______________________________________________
GiDlist mailing list
GiDlist at listas.cimne.upc.edu
http://listas.cimne.upc.edu/cgi-bin/mailman/listinfo/gidlist
HEMMI, Shigeru

[GiDlist] Import->Insert GiD Geometry crashes on Windows 64b

Postby HEMMI, Shigeru » Wed Aug 06, 2014 3:19 pm

Dear Enrique Escolano,

As you wrote, 32bit GiD NOT crashed, though meshing failed (is a
smaller problem).
Please see figures1-6 attached (Sorry many attachments).

Best Regards,

HEMMI, Shigeru

2014-08-06 22:07 GMT+09:00 Enrique Escolano escolano at cimne.upc.edu:
You can set exactly the same meshing preferences than I've used opening my GiD model and selecting the menu
Mesh-Mesh options from model

I've used GiD 11.0.8 Windows x32, maybe the crash only happen in the Windows x64 version (I don't have now any Winx64 machine available to test it)
You can also install and run a Windows x32 version of GiD on a Window x64 operating system.

Note: you can have several GiD versions installed simultaneously, it is not necessary to uninstall other versions, each one is stored in a different folder.

-----Mensaje original-----
De: HEMMI, Shigeru [mailto:textdirected at gmail.com]
Enviado el: miércoles, 6 de agosto de 2014 13:30
Para: Enrique Escolano; gidlist at listas.cimne.upc.edu
Asunto: Re: [GiDlist] Import-Insert GiD Geometry crashes on Windows 64bit

Dear Enrique Escolano,

Thanks for the support but the problem not solved.

Uninstalled GiD11.1.9d-win-x64-Install and installed GiD11.0.8-win-x64, set the 'Reset preferences' checkbox, and open pantheon.gid which is the attachment in your reply mail.

And then I did Erase--Mesh and Generate--Mesh, GiD crashed again.
See the attachment 2 figures.

My PC is Windows 8.1 Pro, 32Gbytes memory equipped.

Best regards,

HEMMI, Shigeru

2014-08-04 23:14 GMT+09:00 Enrique Escolano escolano at cimne.upc.edu:
In my experience GiD 11.0.8 is not so unstable as do you think.
Maybe do you have some settings of a kind of models that are specially
problematic.
I recommend you to reset all your settings (start once with "GiD safe mode"
and set the 'Reset preferences' checkbox)

For example I am able to import the file pantheon.igs with GiD 11.0.8
(Windows x32) , with automatic collapse with default tolerance with
importing, And then to generate the mesh with size=100 I have some
problem: GiD can't mesh, but it doesn't crashed.
Then I've deleted the volume and created it again (maybe some surface
is bad oriented for the volume) and then I am able to mesh it with this size.
I attach my GiD model including the coarse volume mesh.

Enrique

-----Mensaje original-----
De: gidlist-bounces at listas.cimne.upc.edu
[mailto:gidlist-bounces at listas.cimne.upc.edu] En nombre de HEMMI,
Shigeru Enviado el: lunes, 4 de agosto de 2014 14:21
Para: Enrique Escolano; gidlist at listas.cimne.upc.edu
Asunto: Re: [GiDlist] Import-Insert GiD Geometry crashes on Windows
64bit

Dear Enrique Escolano,

1. As you wrote, GiD 11.1.9d does not crash after mesh generated for
both models and I apply "Insert GiD model"; thanks for the support.
2. I do not have money to purchase GiD 12; I have to go with GiD 11
for a while.
3. The last official version 11.0.8 still has another crash problem,
e.g.,

http://www.gidhome.com/component/manual/gidlist2014/panhteonigs_causes
_a_cra sh_of_gid_11_64bit_whengenerating_mesh
, which is not replyed yet. In my experiences the official version
11.0.8 crashes very often in many situations.

Best regards,

HEMMI, Shigeru



2014-08-04 19:46 GMT+09:00 Enrique Escolano escolano at cimne.upc.edu:
If fact the problem happen because in latest GiD developer versions
"Insert GiD geometry" has changed to "Insert GiD model" and now the
mesh is also inserted.

The crash happen if the model to insert or the current model doesn't
has
any mesh. You can avoid the crash in GiD 11.1.9d with some trick, like
generate a mesh in both models before the insertion.

The problem is that we are not compiling any 11.x version more,
because
this version has become the 12 version. The bug has been fixed in
version
12.0.1 available for download now.

You can also use the last 11.0.8 official version.

Enrique Escolano

-----Mensaje original-----
De: HEMMI, Shigeru [mailto:textdirected at gmail.com] Enviado el:
domingo, 3 de agosto de 2014 14:52
Para: Enrique Escolano
Asunto: Re: [GiDlist] Import-Insert GiD Geometry crashes on Windows
64bit

Dear Enrique,

Thanks for the answer but the problem NOT solved.

I saved two models, for example, one is a sphere of radius 1.0 and
the
center placed at the origin, and the second model of another sphere
of radius 1.0 at the center (2.0,0,0). When I open the first model and
go to "import--insert GiD Geometry" choosing the second model, GiD
crashes on my Windows PC.

Since the "import--insert GiD Geomtry" feature is significant for my
work, please fix it and provide fixed GiD 11 module.

Best regards,

HEMMI, Shigeru

2014-07-30 18:14 GMT+09:00 Enrique Escolano escolano at cimne.upc.edu:
It seems that it crash only when inserting a model in an empty model.
For this case doesn't has sense to use insert, use the normal open.
Insert model is just interesting to add a model to an existing model.

We will fix it for next GiD 12.0.1 version

Thanks for your information

Enrique

-----Mensaje original-----
De: gidlist-bounces at listas.cimne.upc.edu
[mailto:gidlist-bounces at listas.cimne.upc.edu] En nombre de HEMMI,
Shigeru Enviado el: martes, 29 de julio de 2014 23:41
Para: gidlist at listas.cimne.upc.edu
Asunto: [GiDlist] Import-Insert GiD Geometry crashes on Windows
64bit

Dear GiD team,

I have a problem of GiD crash.

When I try
Files--Import--Insert GiD model
and choose some model then crash.

I am using GiD 11.1.9d 64bit on Windows 8.1 pro 64bit.

Thanks in advance,

HEMMI, Shigeru
_______________________________________________
GiDlist mailing list
GiDlist at listas.cimne.upc.edu
http://listas.cimne.upc.edu/cgi-bin/mailman/listinfo/gidlist


_______________________________________________
GiDlist mailing list
GiDlist at listas.cimne.upc.edu
http://listas.cimne.upc.edu/cgi-bin/mailman/listinfo/gidlist

-------------- next part --------------
A non-text attachment was scrubbed...
Name: GiD32bit_NOT_crash_Fig1.PNG
Type: image/png
Size: 704479 bytes
Desc: not available
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140806/7c6da549/attachment-0006.png
-------------- next part --------------
A non-text attachment was scrubbed...
Name: GiD32bit_NOT_crash_Fig2.PNG
Type: image/png
Size: 188752 bytes
Desc: not available
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140806/7c6da549/attachment-0007.png
-------------- next part --------------
A non-text attachment was scrubbed...
Name: GiD32bit_NOT_crash_Fig3.PNG
Type: image/png
Size: 234045 bytes
Desc: not available
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140806/7c6da549/attachment-0008.png
-------------- next part --------------
A non-text attachment was scrubbed...
Name: GiD32bit_NOT_crash_Fig4.png
Type: image/png
Size: 172232 bytes
Desc: not available
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140806/7c6da549/attachment-0009.png
-------------- next part --------------
A non-text attachment was scrubbed...
Name: GiD32bit_NOT_crash_Fig5.PNG
Type: image/png
Size: 174647 bytes
Desc: not available
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140806/7c6da549/attachment-0010.png
-------------- next part --------------
A non-text attachment was scrubbed...
Name: GiD32bit_NOT_crash_Fig6.PNG
Type: image/png
Size: 203018 bytes
Desc: not available
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20140806/7c6da549/attachment-0011.png

Return to “2014”

Who is online

Users browsing this forum: No registered users and 1 guest