[GiDlist] A bug about polyline

Moderator: GiD Team

Post Reply
ÖÜÉÙÁÖ

[GiDlist] A bug about polyline

Post by ÖÜÉÙÁÖ »

HI:
I find a bug in Gid.When I have created a PolyLine and extrude it to a
surface.Then if you will render it you will find a erro surface.I attched an
example.





--http://www.eyou.com
--Îȶ¨¿É¿¿µÄÃâ·Ñµç×ÓÐÅÏä ÓïÒôÓʼþ Òƶ¯ÊéÇ© ÈÕÀú·þÎñ ÍøÂç´æ´¢...ÒÚÓÊδ¾¡

-------------- next part --------------
A non-text attachment was scrubbed...
Name: 1.gid.rar
Type: application/octet-stream
Size: 559 bytes
Desc: not available
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20020912/717a48d3/attachment.obj
Enrique Escolano

[GiDlist] A bug about polyline

Post by Enrique Escolano »

The compressed rar file is corrupted,
please send us another copy of the .geo file.

Enrique

----- Original Message -----
From: "ÖÜÉÙÁÖ" fea at eyou.com
To: gidlist at gatxan.cimne.upc.es
Sent: Thursday, September 12, 2002 1:22 PM
Subject: [GiDlist] A bug about polyline


HI:
I find a bug in Gid.When I have created a PolyLine and extrude it to a
surface.Then if you will render it you will find a erro surface.I attched
an
example.





--http://www.eyou.com
--Îȶ¨¿É¿¿µÄÃâ·Ñµç×ÓÐÅÏä ÓïÒôÓʼþ Òƶ¯ÊéÇ© ÈÕÀú·þÎñ
ÍøÂç´æ´¢...ÒÚÓÊδ¾¡


kenji furui

[GiDlist] Q about mesh generation

Post by kenji furui »

Dear GiD members,

I have often got errors when creating unstructured
meshes (mainly tetrahedras) over the particular
complex domain/volume. (Please take a look at the
attachment Geo file.)
There is a volume which contains some narrow holes.
I'm wondering if I need to divide it into some sub
domains...
Does anybody know the best way to avoid these errors?

thanks always,

kenji furui
Dept. Petroleum Engineering
The University of Texas at Austin




__________________________________________________
Do you Yahoo!?
Yahoo! News - Today's headlines
http://news.yahoo.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: skinm4_1vv.geo
Type: application/octet-stream
Size: 126871 bytes
Desc: skinm4_1vv.geo
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20020914/74474685/attachment.obj
kenji furui

[GiDlist] mesh generation2

Post by kenji furui »

Dear GiD members,

Please use this geo file instead of the attachment in
my previous email.
I would like to have meshes under the following
conditions;

Element size on cavities (perforations); 0.04
(smaller is ok)
@Size transition; 0.6-0.8


thanks,

kenji (GiD ver7.1 user)



__________________________________________________
Do you Yahoo!?
Yahoo! News - Today's headlines
http://news.yahoo.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: skinm4_1vv.geo
Type: application/octet-stream
Size: 126871 bytes
Desc: skinm4_1vv.geo
Url : http://listas.cimne.upc.edu/pipermail/gidlist/attachments/20020914/20599ce9/attachment.obj
VSayako Willy

[GiDlist] Render beam element

Post by VSayako Willy »

Hi GiD team

I just would like to ask if GiD,the future Version,
can render the beam element as their properties
instead of single line but element section??
Like I beam, U beam, C beam and so on..with all
options of deformed shape and contour in post
processing???


Best Regards.



__________________________________________________
Do you Yahoo!?
Yahoo! News - Today's headlines
http://news.yahoo.com
Ramon Ribó

[GiDlist] mesh generation2

Post by Ramon Ribó »

Hello,

When there are problems in meshing, a possible procedure to
follow is this:

- Use meshing-Mesh criteria-Mesh surfaces and select all surfaces.
- Mesh again
- Investigate the mesh shape, specially near the points where GiD
exposes problems

In your particular case, the mesh over the thick cilinders is very
agly. Try to subdivide the associated surfaces with:
Geometry-Edit-Divide-Surfaces-Num divisions.

Regards,

--
Compass Ing. y Sistemas Dr. Ramon Ribó
http://www.compassis.com ramsan at compassis.com
c/ Manuel Girona, 61 bajos tel. +34 93 204 10 82
08034 Barcelona, Spain fax. +34 93 204 19 09

-----Mensaje original-----
De: gidlist-admin at gatxan.cimne.upc.es
[mailto:gidlist-admin at gatxan.cimne.upc.es]En nombre de kenji furui
Enviado el: sábado, 14 de septiembre de 2002 17:19
Para: gidlist at gatxan.cimne.upc.es
Asunto: [GiDlist] mesh generation2


Dear GiD members,

Please use this geo file instead of the attachment in
my previous email.
I would like to have meshes under the following
conditions;

Element size on cavities (perforations); 0.04
(smaller is ok)
@Size transition; 0.6-0.8


thanks,

kenji (GiD ver7.1 user)



__________________________________________________
Do you Yahoo!?
Yahoo! News - Today's headlines
http://news.yahoo.com
Ramon Ribó

[GiDlist] Render beam element

Post by Ramon Ribó »

Hello,

In order for GiD to be able to render the beams
with his cross-section shape, it would be necessary
to create a way for defining the shapes. One possibility
would be to take advantage of the geometry defined
in the .sim file.

This can be a very interesting capability to be
added for next versions.

Best regards,

--
Compass Ing. y Sistemas Dr. Ramon Ribó
http://www.compassis.com ramsan at compassis.com
c/ Manuel Girona, 61 bajos tel. +34 93 204 10 82
08034 Barcelona, Spain fax. +34 93 204 19 09

-----Mensaje original-----
De: gidlist-admin at gatxan.cimne.upc.es
[mailto:gidlist-admin at gatxan.cimne.upc.es]En nombre de VSayako Willy
Enviado el: lunes, 16 de septiembre de 2002 5:06
Para: gidlist at gatxan.cimne.upc.es
Asunto: [GiDlist] Render beam element


Hi GiD team

I just would like to ask if GiD,the future Version,
can render the beam element as their properties
instead of single line but element section??
Like I beam, U beam, C beam and so on..with all
options of deformed shape and contour in post
processing???


Best Regards.



__________________________________________________
Do you Yahoo!?
Yahoo! News - Today's headlines
http://news.yahoo.com
_______________________________________________
GiDlist mailing list
GiDlist at gid.cimne.upc.es
http://gid.cimne.upc.es/mailman/listinfo/gidlist
Post Reply