[GiDlist] unstructured meshes

Moderator: GiD Team

Post Reply
Mark Smith

[GiDlist] unstructured meshes

Post by Mark Smith »

Dear GiD team

Do you have any plans to extend the element types available for unstructured
meshes from just triangle (2D) and tets (3D) to be able to use for 3D,
prisms (6 node) pyramid (5 node) brick (8 node) (linear versions) in your
auto meshing routines?
I am finding triangle & tet only somewhat limiting when the FEA package I
use for the analysis has many more types available.
Regards
Mark


--------------------------------------------------------------------------
Linx Printing Technologies plc
+44 (0)1480302100
http://www.linx.co.uk/
This e-mail may contain privileged/confidential information and may be
read, copied and used only by the intended recipient. If you have received
it in error, please contact the sender by return e-mail or by
telephoning +44 (0)1480 302100.
Please then delete the e-mail and do not disclose its contents to any
person.

Any information in this message that does not relate to the official
business of Linx shall be understood as neither given nor endorsed by Linx.
We reserve the right to monitor all e-mail communications through our
internal and external networks.
--------------------------------------------------------------------------
Enrique Escolano

[GiDlist] unstructured meshes

Post by Enrique Escolano »

For future versions are planning to mesh prisms (structured in a direction,
as
a offset of surface triangles) to use specially in CFD analysis.

To mesh with bricks is of interest for some codes, but the hexahedra it is a
bad shape to fill unstructured a generic volume. (it could be in a long
term)

The pyramid elements in principle they seem of little interest.

We are also working in other less conventional mesh types, like for example
the
case of points or spheres for input of "meshless" codes.

Regards

Enrique Escolano

----- Original Message -----
From: "Mark Smith" mark.smith at linx.co.uk
To: "Gidlist (E-mail)" gidlist at gatxan.cimne.upc.es
Sent: Thursday, July 18, 2002 6:33 PM
Subject: [GiDlist] unstructured meshes


Dear GiD team

Do you have any plans to extend the element types available for
unstructured
meshes from just triangle (2D) and tets (3D) to be able to use for 3D,
prisms (6 node) pyramid (5 node) brick (8 node) (linear versions) in your
auto meshing routines?
I am finding triangle & tet only somewhat limiting when the FEA package I
use for the analysis has many more types available.
Regards
Mark


--------------------------------------------------------------------------
Linx Printing Technologies plc
+44 (0)1480302100
http://www.linx.co.uk/
This e-mail may contain privileged/confidential information and may be
read, copied and used only by the intended recipient. If you have received
it in error, please contact the sender by return e-mail or by
telephoning +44 (0)1480 302100.
Please then delete the e-mail and do not disclose its contents to any
person.

Any information in this message that does not relate to the official
business of Linx shall be understood as neither given nor endorsed by
Linx.
We reserve the right to monitor all e-mail communications through our
internal and external networks.
--------------------------------------------------------------------------



_______________________________________________
GiDlist mailing list
GiDlist at gid.cimne.upc.es
http://gid.cimne.upc.es/mailman/listinfo/gidlist

Shuo Ma

[GiDlist] gid7 for Sun system

Post by Shuo Ma »

Hi Miguel,

Did you receive my e-mails? I was waiting for your answer. I know there must be
problems with Gid on the Sun system. Is it easy to fix?

I'll use Gid to generate more than 10 million nodes for my 3D finite element
mesh. I was wondering how much memory it needs. I know this certainly cannot be
done on a PC. In our institute there is a 8 GB memory Sun system. But
unfortunately, I met some problems with Gid on the Sun as my previous e-mails
mentioned.

I contacted the coordinator in the San Diego Supercomputer Center and try to use
their computer. But I don't know whether Gid works on their system.

regards,
Shuo Ma
Miguel A. de Riera Pasenau

[GiDlist] gid7 for Sun system

Post by Miguel A. de Riera Pasenau »

hello,
yes we've received your email,
we're working on it trying to find the problem,
we are using a sun from another department.

have you tried to use the version 6.1.3 for Sun?
did you get the same problem?
ftp://gid.cimne.com/pub/gid/Sun/gid6.1.3.tar.gz
you can still get a one month password for this version
http://gid.cimne.com/password/pa01.subst

miguel

Shuo Ma wrote:

Hi Miguel,

Did you receive my e-mails? I was waiting for your answer. I know there must be
problems with Gid on the Sun system. Is it easy to fix?

I'll use Gid to generate more than 10 million nodes for my 3D finite element
mesh. I was wondering how much memory it needs. I know this certainly cannot be
done on a PC. In our institute there is a 8 GB memory Sun system. But
unfortunately, I met some problems with Gid on the Sun as my previous e-mails
mentioned.

I contacted the coordinator in the San Diego Supercomputer Center and try to use
their computer. But I don't know whether Gid works on their system.

regards,
Shuo Ma

_______________________________________________
GiDlist mailing list
GiDlist at gid.cimne.upc.es
http://gid.cimne.upc.es/mailman/listinfo/gidlist

--
--------------------------------------------------------------------------------
Miguel A. de Riera Pasenau miguel at cimne.upc.es http://gid.cimne.upc.es
Shuo Ma

[GiDlist] bas file for contact problems

Post by Shuo Ma »

Hello Miguel,

Is there any progress for Gid on the Sun system?

Recently I am trying to use Gid to mesh contact problems. But I don't know
how to write the condition and bas files for the contact condition. How do I
write bas file to get the node pairs on the contact surface in my
calculation file?

Regards,
Shuo Ma

----- Original Message -----
From: "Miguel A. de Riera Pasenau" miguel at cimne.upc.es
To: gidlist at gatxan.cimne.upc.es&gt "Jorge Suit Perez Ronda"
ronda at cimne.upc.es
Sent: Friday, July 19, 2002 12:25 AM
Subject: Re: [GiDlist] gid7 for Sun system


hello,
yes we've received your email,
we're working on it trying to find the problem,
we are using a sun from another department.

have you tried to use the version 6.1.3 for Sun?
did you get the same problem?
ftp://gid.cimne.com/pub/gid/Sun/gid6.1.3.tar.gz
you can still get a one month password for this version
http://gid.cimne.com/password/pa01.subst

miguel

Shuo Ma wrote:

Hi Miguel,

Did you receive my e-mails? I was waiting for your answer. I know there
must be
problems with Gid on the Sun system. Is it easy to fix?

I'll use Gid to generate more than 10 million nodes for my 3D finite
element
mesh. I was wondering how much memory it needs. I know this certainly
cannot be
done on a PC. In our institute there is a 8 GB memory Sun system. But
unfortunately, I met some problems with Gid on the Sun as my previous
e-mails
mentioned.

I contacted the coordinator in the San Diego Supercomputer Center and
try to use
their computer. But I don't know whether Gid works on their system.

regards,
Shuo Ma

_______________________________________________
GiDlist mailing list
GiDlist at gid.cimne.upc.es
http://gid.cimne.upc.es/mailman/listinfo/gidlist

--
--------------------------------------------------------------------------
------
Miguel A. de Riera Pasenau miguel at cimne.upc.es
http://gid.cimne.upc.es
_______________________________________________
GiDlist mailing list
GiDlist at gid.cimne.upc.es
http://gid.cimne.upc.es/mailman/listinfo/gidlist


Post Reply