[GiDlist] adding a point to a geometry

Moderator: GiD Team

Post Reply
Gassan Abdoulaev

[GiDlist] adding a point to a geometry

Post by Gassan Abdoulaev »

Hello,

Is it possible to add a point (points)
to an existing geometry, say, a cylinder,
so that the GID mesh generator will produce
mesh nodes at given points.

Thank you in advance!

Gassan
--
----------------------------------------------------
Gassan Abdoulaev, PhD
Dept. of Biomedical Engineering
Columbia University
Mudd Bldg., ET351, Mail Code 8904
500 West 120th Street, New York, NY 10027, USA
phone: (212)854 5737
fax: (212)854 8725
email: gsa2001 at columbia.edu
Enrique Escolano

[GiDlist] adding a point to a geometry

Post by Enrique Escolano »

No, to force the mesh to share this node it's necessary to divide this
cilinder with a surface that contain
as boundary a line that contain this point.

Enrique

----- Original Message -----
From: "Gassan Abdoulaev" gsa2001 at columbia.edu
To: gidlist at gatxan.cimne.upc.es
Sent: Thursday, April 29, 2004 4:08 PM
Subject: [GiDlist] adding a point to a geometry


Hello,

Is it possible to add a point (points)
to an existing geometry, say, a cylinder,
so that the GID mesh generator will produce
mesh nodes at given points.

Thank you in advance!

Gassan
--
----------------------------------------------------
Gassan Abdoulaev, PhD
Dept. of Biomedical Engineering
Columbia University
Mudd Bldg., ET351, Mail Code 8904
500 West 120th Street, New York, NY 10027, USA
phone: (212)854 5737
fax: (212)854 8725
email: gsa2001 at columbia.edu

_______________________________________________
GiDlist mailing list
GiDlist at gid.cimne.upc.es
http://gid.cimne.upc.es/mailman/listinfo/gidlist

Gassan Abdoulaev

[GiDlist] adding a point to a geometry

Post by Gassan Abdoulaev »

Well, this is very inconvenient. There are many situations
when it's necessary to add a node, or a line, or a surface.

Thank you anyway.

Gassan

Enrique Escolano wrote:
No, to force the mesh to share this node it's necessary to divide this
cilinder with a surface that contain
as boundary a line that contain this point.

Enrique

----- Original Message -----
From: "Gassan Abdoulaev" gsa2001 at columbia.edu
To: gidlist at gatxan.cimne.upc.es
Sent: Thursday, April 29, 2004 4:08 PM
Subject: [GiDlist] adding a point to a geometry



Hello,

Is it possible to add a point (points)
to an existing geometry, say, a cylinder,
so that the GID mesh generator will produce
mesh nodes at given points.

Thank you in advance!

Gassan
--
----------------------------------------------------
Gassan Abdoulaev, PhD
Dept. of Biomedical Engineering
Columbia University
Mudd Bldg., ET351, Mail Code 8904
500 West 120th Street, New York, NY 10027, USA
phone: (212)854 5737
fax: (212)854 8725
email: gsa2001 at columbia.edu

_______________________________________________
GiDlist mailing list
GiDlist at gid.cimne.upc.es
http://gid.cimne.upc.es/mailman/listinfo/gidlist



_______________________________________________
GiDlist mailing list
GiDlist at gid.cimne.upc.es
http://gid.cimne.upc.es/mailman/listinfo/gidlist


--
----------------------------------------------------
Gassan Abdoulaev, PhD
Dept. of Biomedical Engineering
Columbia University
Mudd Bldg., ET351, Mail Code 8904
500 West 120th Street, New York, NY 10027, USA
phone: (212)854 5737
fax: (212)854 8725
email: gsa2001 at columbia.edu
Post Reply