Contact Us
 

Contact CIMNE

    International Center for Numerical Methods in Engineering
    C1 Building, Campus Norte UPC
    Gran Capitan, s/n
    08034 Barcelona, Spain

Login
 
 
Online User Manual | Print |
GiD 11 User Manual
Pre and post processing system for Numerical Simulations.
International Center For
Numerical Methods In Engineering (CIMNE)

Russian pdf and online version. Tranlated by Irene Grigorieva from University of Kemerovo, Russia.


                  INTRODUCTION
                        User interface
                        Models used in this manual
                  INITIATION TO GiD
                        First steps
                        Creation and meshing of a line
                        Creation and meshing of a surface
                        Creation and meshing of a volume
                  IMPLEMENTING A MECHANICAL PART
                        Working by layers
                              Defining the layers
                              Creating two new layers
                        Creating a profile
                              Creating a size-55 auxiliary line
                              Dividing the auxiliary line near coordinates (40, 0)
                              Creating a 3.8-radius circle around point (40, 0)
                              Rotating the circle -3 degrees around a point
                              Rotating the circle 36 degrees around a point and copying it
                              Rotating and copying the auxiliary lines
                              Intersecting lines
                              Creating an arc tangential to two lines
                              Translating the definitive lines to the "profile" layer
                              Deleting the "aux" layer
                              Rotating and obtaining the final profile
                              Creating a surface
                        Creating a hole in the mechanical part
                              Creating a hole in the surface of the mechanical part
                        Creating volumes from surfaces
                              Creating the "prism" layer and translating the octagon to this layer
                              Creating the volume of the prism
                              Creating the volume of the wheel
                        Generating the mesh
                              Generating the mesh by default
                              Generating the mesh with assignment of size around points
                              Generating the mesh with assignment of size around lines
                        Optimizing the design of the mechanical part
                              Modifying the profile
                              Modifying the profile of the hole
                              Creating the volume of the new design
                        Generating the mesh for the new design
                              Generating a mesh for the new design by default
                              Generating a mesh using "Chordal Error"
                  IMPLEMENTING A COOLING PIPE
                        Working by layers
                              Creating two new layers
                        Creating the auxiliary lines
                              Creating the axes
                              Creating the tangential center
                        Creating a component part
                              Creating the profile
                              Creating the volume by revolution
                              Creating the union of the main pipes
                              Rotating the main pipe
                              Creating the end of the pipe
                        Creating the T junction
                              Creating one of the pipe sections
                              Creating the other pipe section
                              Creating the lines of intersection
                              Deleting surfaces and lines
                              Closing the volume
                        Importing the T junction to the main file
                              Importing a GiD file
                              Creating the final volume
                        Generating the mesh
                              Generating the mesh using Chordal Error
                              Generating the mesh by assignment of sizes on surfaces
                  ASSIGNING ELEMENT SIZES
                        Introduction
                              Reading the initial project
                        Element-size assignment methods
                              Assignment using default options
                              Assignment around points
                              Assignment around lines
                              Assignment on surfaces
                              Assignment with Maximum Chordal Error
                        Rjump mesher
                              RJump default options
                              Force to mesh some entity
                  METHODS FOR MESH GENERATION
                        Introduction
                              Reading the initial project
                        Types of mesh
                              Generating the mesh by default
                              Generating the mesh using circles and spheres
                              Generating the mesh using points
                              Generating the mesh using quadrilaterals
                              Generating a structured mesh (surfaces)
                              Generating structured meshes (volumes)
                              Generating semi-structured meshes (volumes)
                              Concentrating elements and assigning sizes
                              Generating the mesh using quadratic elements
                  POSTPROCESSING
                        Loading the model
                        Changing mesh styles
                        Viewing the results
                              Iso surfaces
                              Animate
                              Result surface
                              Contour fill, cuts and limits
                              Combined results
                              Stereo mode (3D)
                              Show Min Max
                              Stream lines
                              Graphs
                        Creating images
                  IMPORTING FILES
                        Importing on GiD
                              Importing an IGES file
                        Correcting errors in the imported geometry
                              Meshing by default
                              Correcting surfaces
                        The conformal mesh and the non-conformal mesh
                              Global collapse of the model
                              Correcting surfaces and creating a conformal mesh
                              Creating a non-conformal mesh
                              Optimizing a non-conformal mesh
                  DEFINING A PROBLEM TYPE
                        Introduction
                              Interaction of GiD with the calculating module
                        Implementation
                              Creating the Materials File
                              Creating the General File
                              Creating the Conditions File
                              Creating the Data Format File (Template file)
                              Creating the Execution file of the Calculating Module
                              Creating the Execution File for the Problem Type
                        Using the problemtype with an example
                              Executing the calculation with a concentrated weight
                        Aditional information
                              The main program